Send an enquiry
Sourcing agent · Shot peening & surface treatment equipment

The right peening machine for your part, from the right builder.

Arcalmen does not build machines. We work out the system your workpiece needs, source it from competitive manufacturers, and handle the conversation from first drawing to final acceptance.

Specs we work toSAE J443SAE J2277AMS 2430AMS 2432NADCAP
Workpiece 01 / 05
Spur gear
Rotation 000°
Media S230
Coverage 0%
Workpieces we handle · 01

Gears & gear shafts

Tooth roots carry the highest bending stress in a gearbox. Peening them adds compressive stress that holds back fatigue cracks, so the machine has to reach every root at a controlled angle.

Areas
Tooth roots and flanks, spline runouts
Media
Cast steel shot S170–S330, conditioned cut wire
Handling
Exchange table with 2 to 8 stations, loading robot if needed
Workpieces we handle · 02

Coil & leaf springs

Springs are peened in high volumes, often straight after heat treatment. Lines are built for flow: parts roll through the blast zone while wheels or nozzles cover the inside diameter and the outer surface.

Areas
Coil ID and OD, leaf tension side
Media
Conditioned cut wire 0.4–1.0 mm
Handling
Through-feed conveyor, stress-peening fixtures
Workpieces we handle · 03

Turbine blades

Aerospace and power parts need repeatable, documented peening. A robot guides the gun along the blade profile while the turntable sets the angle, and the controller logs pressure and media flow for every part.

Areas
Fir-tree and dovetail roots, airfoils
Media
Ceramic beads, glass beads, fine cast steel shot
Handling
Swing arm or two-station exchange table, 6-axis robot
Workpieces we handle · 04

Blisks & compressor discs

On a blisk the blades and the disc are one forged part. After a repair blend, the reworked area is peened again on the spot, with two guns working both sides of the airfoil at once so the blade does not distort.

Areas
Blended airfoil areas, leading edges, disc web and bore
Media
Ceramic beads, fine cast steel shot S110–S170
Handling
Swing arm, turntable as a robot axis
Workpieces we handle · 05

Crankshafts & long shafts

Heavy and long parts ride on a work car, one end in a chuck and the other on roller supports. The car runs into the chamber, the part turns slowly, and the guns travel along it to reach every fillet radius.

Areas
Fillet radii, journals, bearing seats
Media
Cast steel shot S230–S550, ceramic for shafts
Handling
Work car with chuck and roller supports, crane loading
Configurator

One cell, many combinations

Blasting and peening machines are classified by five choices: how the part moves, how the gun moves, how media is fed, how it is recovered, and how big the chamber is. Scroll to change one choice at a time.

Configuration
ARC-ET-MA-P1-PN-1800
Layout
–
Part handlingExchange table
Gun movementCNC manipulator
Media feedPressure pot
RecoveryPneumatic
Chamber1800 × 1550 × 2000 mm
Part handling 1 / 5

Exchange table

The main door itself turns ±180° and carries 2, 4, 6 or 8 stations. One side is loaded while the other is peened, each station spinning its part at 3 to 30 rpm. Inflatable seals close the door; a light curtain guards the loading side.

Suited to
Automotive gears, flexsplines, high-volume small parts
Part handling 2 / 5

Swing arm

A servo-driven arm swings the turntable out through the door onto a waffle-plate floor for loading, then back in, where a pin locks it in position. The turntable can run as an external robot axis.

Suited to
Aero-engine blades, blisks, turbine discs
Part handling 3 / 5

Work car

A rail car carries the part in and out at 3 to 5 m/min. A frame table on a slewing ring turns heavy parts at 1 to 10 rpm. Long shafts ride on powered roller supports instead.

Suited to
Wind-power gears, landing gear, drill tools, long shafts
Part handling 4 / 5

Satellite table

Several satellites sit on one indexing table in the middle of the chamber. Each satellite spins its part while the operator loads the next one at the door.

Suited to
Gears, gear shafts and hubs in series production
Part handling 5 / 5

Through-feed conveyor

Parts ride a conveyor straight through the chamber, under blast wheels. Vestibules with rubber curtains at both ends keep the media inside. A through-feed line is a wheel machine, so the wheels and their screw and bucket elevator come with the conveyor.

Suited to
Coil and leaf springs, bars, castings
Gun movement 1 / 4

Manual cabinet

A sheet-metal cabinet 1.0 to 1.6 m wide on a hopper base. The operator works through glove ports under a sloped window, loads through the side door and blasts from a foot pedal. Cyclone, blast pot and a small dust collector stand beside it.

Suited to
Test pieces, repairs, touch-up after blending
Gun movement 2 / 4

CNC manipulator

An enclosed Z-axis column travels on a Y-axis base on the roof, and a B-axis at the end of the tube swings the gun bar. Ball screws, linear guides and servo drives; a sliding seal keeps the roof slot closed.

Suited to
Rotating parts with simple shapes: gears, shafts, discs
Gun movement 3 / 4

6-axis robot

The robot stands in an aluminium-framed room beside the chamber and wears a protective suit against rebounding shot. It carries whichever gun the part needs, on paths programmed offline.

Suited to
Complex curved surfaces and high-accuracy aerospace parts
Gun movement 4 / 4

Blast wheels

Each wheel sits on its motor shaft and throws the media by centrifugal force, with no compressed air. Media drops from the silo through a flow valve into the hub. The high media flow needs mechanical recovery, so the screw and bucket elevator arrive with the wheels.

Suited to
Batch cleaning and strengthening of gears and castings
Media feed 1 / 5

Suction

A venturi at the gun draws media out of the hopper and into the air stream. Light duty at low air demand, about 1.5 m³/min for an 8 mm gun.

Suited to
Light rust and scale, small parts, fine finishing
Media feed 2 / 5

Gravity feed

Media falls from the hopper to the gun under its own weight, metered by flow valves. Compressed air only accelerates it.

Suited to
Heavy rust, thick scale, large workpieces
Media feed 3 / 5

Pressure pot

The whole pot is pressurised and pushes media into the gun at high speed. A media flow valve per outlet and a closed-loop pressure regulator hold each nozzle on target. The pot stands in line under the storage hopper, inside the tower frame, and connects to the chamber through rubber hoses.

Suited to
Peening and cleaning where quality and output both matter
Media feed 4 / 5

Double pressure pot

Two stacked chambers: the upper one refills while the lower one keeps blasting, so peening never stops to depressurise. Larger units feed more guns at higher flow.

Suited to
Continuous production, multi-gun setups
Media feed 5 / 5

Two or more pot systems

Each storage hopper can feed its own pot, in line below it. Two systems side by side supply more guns or keep a second media ready, and further systems are added the same way.

Suited to
Large multi-gun cells, cells running two media
Media recovery 1 / 3

Pneumatic

A honeycomb floor under the grating feeds a trapezoid duct and a suction hose up to the cyclone. No moving parts and no pit. A rotary airlock passes the media down to the sieve.

Suited to
Aero blades and discs, cells running both steel and ceramic shot
Media recovery 2 / 3

Screw conveyor and bucket elevator

A screw under the chamber feeds a bucket elevator that lifts the media to the sieve. Built for high flow and short cycles: roughly 4.5 t/h per screw and 10 t/h per elevator.

Suited to
High-volume peening, wheel blast machines
Media recovery 3 / 3

Scraper floor and bucket elevator

A reciprocating scraper floor drags the media to the elevator. It handles abrasive media that flow poorly, and it is the usual choice when no foundation pit is possible.

Suited to
Aluminium oxide and other grit, blast rooms
Chamber size any

Sized to your part

There is no catalogue size. The chamber follows your largest part, the reach of the gun device and the door you need, within what fits a truck or a 40 ft container. Keep scrolling to grow the same cell.

1200 × 1000 × 1500 mm
Guns on the stand, left to right

The right gun for each surface

  • OD nozzleA straight-bore nozzle with a boron carbide liner, typically 8 mm, for outer surfaces.
  • Venturi nozzleA converging and diverging bore that speeds the shot up for a wider pattern, at about half as much air again.
  • Rotary lanceA motor spins a thin lance with an angled tip, so a bore is peened evenly all round.
  • Banana nozzleA curved lance that reaches behind flanges and into undercuts.

Every CNC layout also carries a vibrating sieve sized to the media flow, a storage hopper with level sensors, an automatic refilling box and a cartridge dust collector with explosion relief. Models are illustrative; final layouts come from the selected manufacturer.

Ask for your combination
Typical parts

How each part is usually handled

The same five choices, already made for parts we see most. Your part may differ, and that is where the comparison between manufacturers starts.

PartPart handlingGun movement
Automotive gearsFour-station exchange table, two turntables per station, loading robot2-axis manipulator, up and down, in and out
Wind-power gearsWork car with a slewing-ring turntable, 1 to 10 rpm2-axis manipulator
FlexsplinesFour-station exchange table with a shared engagement drive3-axis manipulator with a swing axis, micro-particle media
Aero-engine bladesSwing arm with one large turntable carrying several small ones6-axis robot following the blade profile
BlisksSwing arm, turntable as an external robot axis6-axis robot
Blade-root slotsIndexing table with fixed small turntables2-axis manipulator carrying several gun types
Steam turbine bladesTwo-station exchange table, one turntable per station6-axis robot
Compressor impellers and shaftsWork car with a tilt-and-turn table, 0 to 90°6-axis robot
Landing gearWork car with a chuck and roller supports, plus a centre turntable6-axis robot outside, 3-axis deep-bore lance inside
Drill toolsWork car with powered roller supports2-axis manipulator outside, deep-bore lance inside
Pipe boresPart stays fixedTravelling lance carriage with a deflector tip
Example enquiry

One enquiry, nine processes

An aero-engine MRO shop sent us a single request covering every blasting and peening step in its repair line. We turned it into one specification per process and came back with machine layouts from a shortlisted manufacturer. Customer and manufacturer names are withheld.

What the customer sent
  • Hand blasting
  • Ceramic grit blasting
  • Plastic media blasting
  • Wet Al₂O₃ blasting
  • Glass bead peening
  • Blasting before thermal spray
  • Paint finishing
  • Shot peening
  • High-pressure water jet
Parts
Large rotating parts, long LP shafts, small bores
Peening
Dual guns for blisks, low to high intensity, steel and ceramic media
Control
Robot with offline programming, linked to plant IT
Approvals
Engine OEM manuals (AMM, CMM, EMM) and NADCAP
Loading
By crane, without a large sliding door
What we sent back
  • Robotic shot peening6-axis robot with dual guns, turntable on a swing arm, twin media generators and vibrating sieves
  • Robotic grit blastingRobot-held nozzle, turntable, jib crane, magnetic separator
  • Long-shaft blastingRail carriage with headstock and tailstock, in a chamber as long as the shafts need

Each concept uses a pressure vessel with closed-loop media flow valves. Chamber size, extraction and power were then set for each layout with the manufacturer.

Why an agent

We work for you, not for one factory

An equipment maker can only sell you its own catalogue. As an agent, we start from your part and your budget, then find the manufacturers whose machines fit it best.

Where we sourceFor now, our main manufacturers are in China.

Buying direct

You manage every OEM yourself

  • One catalogue per supplier, each pushing its own design
  • Quotes with different scopes that are hard to compare
  • Specs and drawings explained again to every supplier, often across languages and time zones
  • Build progress, testing and shipping chased by your own team
Through Arcalmen

One contact for the whole search

  • A shortlist of manufacturers chosen for your workpiece
  • Quotes laid out line by line against the same scope
  • Your requirements written once and passed on in each OEM's terms
  • We follow the build, attend acceptance tests and coordinate delivery

Wider choice

We compare several builders and price levels instead of offering one brand.

Less back-and-forth

One technical contact who speaks both peening and procurement.

Fair comparison

Same intensity, coverage and throughput targets in every quote, so price differences are real.

Follow-through

We stay on the project after the order, through testing, installation and handover.

Process

From enquiry sheet to acceptance

  1. Requirements

    You fill in the enquiry sheet: parts, media, volumes, floor space and approvals.

  2. Machine concept

    We settle the five choices: handling, gun movement, media feed, recovery and chamber size.

  3. Capacity check

    Cycle time from surface area and coverage, set against the takt your volumes need.

  4. Itemised quotes

    The same scope goes to several manufacturers and comes back line by line.

  5. Build & FAT

    We follow the build and witness the factory acceptance test with your parts.

  6. Delivery & SAT

    Packing, shipping, installation, site acceptance and training are coordinated for you.

What comes back · 1

Technical specification

  • Cabinet, part movement and gun movement
  • Media generation, recovery and separation
  • Dust collection and electrical control
  • Standards the machine is built to: AMS 2430, 2431 and 2432, SAE J442, J443, J2277 and J2597
What comes back · 2

Itemised quotation

  • Base equipment, broken down by subsystem
  • Part-specific tooling and workholding
  • Spares and wear parts, certification, data collection, training
  • Two totals: F.O.B. seller's dock and D.D.U. your dock, with installation listed separately
What comes back · 3

Capacity and cost appendix

  • Cycle time build-up for each part
  • Machine cycle against required takt, with utilisation
  • Operating cost per piece: power, compressed air, media and wear parts
Equipment we source

Peening and the processes around it

  • CNC shot peening machinesExchange table, work car or swing arm, with a manipulator or a robot
  • Manual cabinets & micro-particle peeningSuction or pressure, from test pieces to flexsplines
  • Blast roomsPneumatic or scraper recovery, work car loading, manual or robot blasting
  • Wheel blast machinesHanger and multi-station machines for batch cleaning and strengthening
  • High-pressure water jetUp to 4000 bar, for stripping coatings from blades in repair
  • Peen formingShaping wing panels by controlled peening
  • Coating & wax stationsSpray stations for corrosion protection
  • Process control & consumablesAlmen gauges and strips, media flow valves, nozzles, media
Enquiry sheet

Tell us about your part

Your name, email and destination country are enough to start. The rest are the facts every manufacturer asks for before a first proposal: fill in what you know. A drawing helps, and can follow by email.

Prefer to write directly? sales@arcalmen.com

You
The part optional
Production and site optional